Loading... Please wait...Currency Displayed in
- Home
- Power
- Power Modules
- MP2722 Evaluation Board
- Home
- Power
- Power Evaluation Boards
- MP2722 Evaluation Board
Categories
Related Products
-
EK-S76GXB Evaluation Board AU$95.00
-
XE132 - EVALUATION BOARD FOR XM132 AU$148.00
-
Evaluation board for AEM10941 AU$129.89
-
-
Evaluation board for AEM30940 - 915 MHz AU$129.89
MP2722 Evaluation Board
Hover over image to zoom
Monolithic Power Systems
)
| This product is available for pre-order only |
Product Description
The EV2722-RH-00A is an evaluation board designed to demonstrate the capabilities of the MP2722, a highly integrated, 5A, switch-mode battery management device for a single-cell Li-ion or Li-polymer batteries. The narrow-voltage DC (NVDC) power management structure provides a low-impedance power path, which optimizes charging efficiency, reduces battery charging time, and extends battery life during discharging.
The MP2722 is fully compliant with USB Type-C 1.3 and supports dual-role port (DRP) functionality, as well as Try.SNK and Try.SRC mode. USB Battery Charging Specification 1.2 (BC 1.2) and non-standard adapter detection are also supported by the input source type identification algorithm.
The serial interface offers complete operating control, charging parameter configuration, and status/interrupt monitoring. The MP2722 supports a fully customizable JEITA profile with configurable temperature windows and actions. It is available in a QFN-22 (2.5mmx3.5mm) package.
The EV2722-RH-00A supports input sources up to 16V, including standard USB host ports and high-voltage wall adapters with fast charge capability. The EV2722-RH-00A supports boost mode and USB On-The-Go (OTG) operation by supplying a voltage between 5V and 5.35V at the IN pin, with up to 3A of current.
Datasheet
Features & Benefits of MP2722
- USB Type-C 1.3 Compliant
- Fully Integrated CC Controller with Dual-Role Port (DRP) Mode and Autonomous or Manual Mode
- Try.SNK and Try.SRC Mode Support
- Supports USB BC 1.2 and Non-Standard Adapters
- 26V Sustainable Input Voltage (VIN)
- Configurable 80mA to 5A Charge Current (ICC) via the Serial Interface
- Configurable 100mA to 3.2A Input Current Limit (IIN_LIM) via the Serial Interface
- Minimum VIN Loop for Maximum Adapter Power Tracking
- Comprehensive Safety Features:
- Fully Customizable JEITA Profile
- Additional Negative Temperature Coefficient (NTC) Thermistor Input
- Configurable Die Temperature Regulation from 60°C to 120°C
- Complete Charge and Pre-Charge Safety Timers
- Watchdog Safety Timer
- Lockable Registers for Charging Parameters
- Configurable 750kHz to 1.5MHz Switching Frequency (fSW)
- Integrated 15mΩ Low On Resistance (RDS(ON)) Battery MOSFET with Shipping Mode and Reset Mode
- Ultra-Low 8.5μA Battery Discharge Current in Shipping Mode
- Down to 30mA Termination Current Settings for Wearable Applications
- Serial Interface Port for Flexible System Parameter Setting and Status Reporting
- Configurable Boost Converter for Source Mode and USB On-The-Go (OTG):
- Configurable Output Current (IOUT) Limit Loop Up to 3A
- Output Over-Current Protection (OCP)
- Ability to Power Large Capacitive Loads Up to 2mF
- Configurable 5V to 5.35V Output Voltage (VOUT)
- Accuracy:
- ±0.5% Battery Regulation Voltage (VBATT_REG)
- ±5% ICC
- ±5% IIN_LIM
- Remote Battery Sensing for Fast Charge
- ±2% Output Regulation in Boost Mode
- Available in a Small QFN-22 (2.5mmx3.5mm) Package